Polaris RZR XP 1000 & XP 4 1000 8”, Billet Portal 45% Gear Lift, (2017) Standard Edition with 16mm Socket, without Frame Stiffener
PGH8-1-33-302-B#RZR
The Portal Advantage
The ultimate UTV lift technology just got bigger with SuperATV’s 8” Portal Gear Lift for the Polaris RZR XP 1000. It doesn’t get any better than a massive 8-inch lift that maintains your axle geometry. The 45 percent gear reduction gives you all the torque you need to push 40” tires through thick mud and over massive boulders. It’s Gear Driven Performance at its finest.
NEW to 8” Portals
Our 8” portals for the RZR XP 1000 feature a 1.5” forward and rear offset. This gives you room for bigger tires—up to 40” without any other modifications.
The drive gear now seals internally against the housing, not the axle. Even if your axle is dirty, dinged up, or otherwise well-used, the drive gear still seals perfectly and keeps all contaminates out of your portal box.
To ensure the rest of the box is sealed, we utilize a new O-ring gasket in a machined groove that keeps oil in and mud out, no matter how deep you go.
FITMENT
Polaris RZR XP 1000 : 2017 with 16mm Socket
Polaris RZR XP 4 1000 : 2017 with 16mm Socket
Polaris RZR XP Turbo : 2017 with 16mm Socket
Polaris RZR XP 4 Turbo : 2017 with 16mm Socket
For Polaris XP 1000 2017 Models: Please check the bolt size of the hardware that fastens the RSL to the brace plate (see image below). Select the socket size that corresponds to your OEM size.
The ultimate UTV lift technology just got bigger with SuperATV’s 8” Portal Gear Lift for the Polaris RZR XP 1000. It doesn’t get any better than a massive 8-inch lift that maintains your axle geometry. The 45 percent gear reduction gives you all the torque you need to push 40” tires through thick mud and over massive boulders. It’s Gear Driven Performance at its finest.
NEW to 8” Portals
Our 8” portals for the RZR XP 1000 feature a 1.5” forward and rear offset. This gives you room for bigger tires—up to 40” without any other modifications.
The drive gear now seals internally against the housing, not the axle. Even if your axle is dirty, dinged up, or otherwise well-used, the drive gear still seals perfectly and keeps all contaminates out of your portal box.
To ensure the rest of the box is sealed, we utilize a new O-ring gasket in a machined groove that keeps oil in and mud out, no matter how deep you go.
FITMENT
Polaris RZR XP 1000 : 2017 with 16mm Socket
Polaris RZR XP 4 1000 : 2017 with 16mm Socket
Polaris RZR XP Turbo : 2017 with 16mm Socket
Polaris RZR XP 4 Turbo : 2017 with 16mm Socket
For Polaris XP 1000 2017 Models: Please check the bolt size of the hardware that fastens the RSL to the brace plate (see image below). Select the socket size that corresponds to your OEM size.
Pricing:
$4,499.95
Description
45% Gear Reduction?
The 45 percent gear reduction (1.82:1 gear ratio) at the hub removes the stress of turning tires from your machine. It’s a monster lift, but it extends the life of your axles and driveline instead beating on it. Axles keep their factory angles. It’s big, it’s practical, and it could only be made by the experts at SuperATV. It’s Gear Driven Performance.
What Are Micro Polished Gears?
If you want maximum performance, choose our precision ground Micro Polished Gears. Micro Polishing is a process that gently smooths out any imperfections in the surface of the metal during a two-stage, non-abrasive, burnishing process that produces a chrome-like finish. The result is unbelievably smooth gears that have almost zero friction or resistance. This means better oil retention and a longer lifetime than other gears. They will stay cool and quiet, while giving you a little more power to the ground.
Do I need a Frame Stiffener?
Yes, we highly recommend running a SuperATV Frame Stiffener with your 8" Portal Gear Lift. Why? When you push the limits and go big with your RZR XP 1000, the stock frame just doesn't have what it takes. Drive too fast or bump too hard and the OEM frame will bend. Trust us — we've done it. A frame stiffener reinforces your frame enough to let you ride your 8" portals with monster tires and no worries.
Performance
-45% gear reduction
-1.5" forward and rear offset maximum
No Leak - Bearings and Seals
-First in the industry thrust bearing that is specifically designed to take axial load, unlike the standard bearing that is only sufficient for radial loads
-Automotive grade bearings
-Press fit, precision ground gears and shafts to eliminate unwanted slop
-Sealed drive gear for peak performance with any axle
-O-ring gasket seals housing halves for leak-free riding
Precision-Ground Gears: Drive Gear, Idler Gear and Driven Gear
-Eliminates friction for reduced heat
-Quiet gears at all speeds
-Allows you to run at higher speeds
Gen 2 Portal Drive Shaft
-Designed to be unbreakable
-Made of 4340 hardened steel
-1.5 in diameter (40 mm)
-M30 threads
Mounting Plates and Pivot Blocks
-CNC formed, fully gusseted 5/16" mounting plates
-Forged pivot blocks
-Carbon steel caliper mounting plates
Gen 2 Slotted Rotors for Unmatched Cooling
-Each wheel hub includes 4 bolt patterns 4/156, 4/137, 4/115, 4/110
-Ability to utilize different wheels on same hub
-Extra thick hub designed to handle any torque
-Stainless steel, braided brake lines included in each kit
Wheel Requirements
-Requires a 22" or larger wheel
-Wheels cannot exceed 5" backspacing
Tire Size
Suspension Setup/ Max Tire Size
Stock/ 40"
1.5" Forward Front A-Arms/ 42"
1.5" Forward Front A-Arms and 3-5" Lift Kit/ 44"
7-10" Lift Kit/ 50"
Measurements were taken with suspension fully compressed and at max turn. Although these are not fully representative of normal riding conditions, stated tire sizes will not rub. With minimal rubbing or trimming, larger sizes can be used.
The 45 percent gear reduction (1.82:1 gear ratio) at the hub removes the stress of turning tires from your machine. It’s a monster lift, but it extends the life of your axles and driveline instead beating on it. Axles keep their factory angles. It’s big, it’s practical, and it could only be made by the experts at SuperATV. It’s Gear Driven Performance.
What Are Micro Polished Gears?
If you want maximum performance, choose our precision ground Micro Polished Gears. Micro Polishing is a process that gently smooths out any imperfections in the surface of the metal during a two-stage, non-abrasive, burnishing process that produces a chrome-like finish. The result is unbelievably smooth gears that have almost zero friction or resistance. This means better oil retention and a longer lifetime than other gears. They will stay cool and quiet, while giving you a little more power to the ground.
Do I need a Frame Stiffener?
Yes, we highly recommend running a SuperATV Frame Stiffener with your 8" Portal Gear Lift. Why? When you push the limits and go big with your RZR XP 1000, the stock frame just doesn't have what it takes. Drive too fast or bump too hard and the OEM frame will bend. Trust us — we've done it. A frame stiffener reinforces your frame enough to let you ride your 8" portals with monster tires and no worries.
Performance
-45% gear reduction
-1.5" forward and rear offset maximum
No Leak - Bearings and Seals
-First in the industry thrust bearing that is specifically designed to take axial load, unlike the standard bearing that is only sufficient for radial loads
-Automotive grade bearings
-Press fit, precision ground gears and shafts to eliminate unwanted slop
-Sealed drive gear for peak performance with any axle
-O-ring gasket seals housing halves for leak-free riding
Precision-Ground Gears: Drive Gear, Idler Gear and Driven Gear
-Eliminates friction for reduced heat
-Quiet gears at all speeds
-Allows you to run at higher speeds
Gen 2 Portal Drive Shaft
-Designed to be unbreakable
-Made of 4340 hardened steel
-1.5 in diameter (40 mm)
-M30 threads
Mounting Plates and Pivot Blocks
-CNC formed, fully gusseted 5/16" mounting plates
-Forged pivot blocks
-Carbon steel caliper mounting plates
Gen 2 Slotted Rotors for Unmatched Cooling
-Each wheel hub includes 4 bolt patterns 4/156, 4/137, 4/115, 4/110
-Ability to utilize different wheels on same hub
-Extra thick hub designed to handle any torque
-Stainless steel, braided brake lines included in each kit
Wheel Requirements
-Requires a 22" or larger wheel
-Wheels cannot exceed 5" backspacing
Tire Size
Suspension Setup/ Max Tire Size
Stock/ 40"
1.5" Forward Front A-Arms/ 42"
1.5" Forward Front A-Arms and 3-5" Lift Kit/ 44"
7-10" Lift Kit/ 50"
Measurements were taken with suspension fully compressed and at max turn. Although these are not fully representative of normal riding conditions, stated tire sizes will not rub. With minimal rubbing or trimming, larger sizes can be used.
Details
- PGH8-1-33-302-B#RZR
- PGH8-1-33-302-B#RZR
- SuperATV
- New
Categories
Shipping Information
- Item Requires Shipping
- 75.0 lbs.
- W20.0000” x H20.0000” x L24.0000”
- Free Shipping
Customer Reviews
Total Reviews (0)
You must login to post a review.
Write the First Review!